Altec Lansing Industrial Professional Sound Products Spec site

ALTEC LANSING INDUSTRIAL PROFESSIONAL SOUND PRODUCTS AMPLIFIER LIST

Altec Amplifier Specification section

 

 

CLICK ON ANY IMAGE TO VIEW THAT EQUIPMENT SECTION

 

Altec 1407A and 1415A Power Amplifier

(page 3)

 

<< Previous

Altec 1407A 1415A Amplifier page 3

CLICK IMAGE TO VIEW FULL RESOLUTION SCAN IMAGE

 

SPECIFICATIONS FOR THE 1407A AND 1415A POWER AMPLIFIERS

1415A Transformer 1 - 300 Hz high pass filter
Output (Balanced) 25 vrms/4.2 0 switch 34.6 vrms/8 Q
70.7 vrms/33.3 Q Amplifier/Load
Protection Short Circuited loads
1407A Direct 24.5 vrms/8 i2 Excessive load reactance
Output RE
(Unbalanced) Excessive temperatuC Power
Requirements 100, 120, 200, 220, or
1407A Transformer 17.3 vrms/4 S2 240 vac, 50/60 Hz, Output 25 vrms/8.3 0
Balanced) 70.7 vrms/66.7 Q Power Consumption/Heat Generated
1415A (Max. 365 watts/580 BTU/hr Damping Factor > 50 output power)
(20 Hz - 1 kHz, 1407A (Max. 175 watts/255 BUT/hr
direct output) output power)

Output Regulation 1415A (1/3 rd Max. 230 watts/560 BTU/hr
(Ref. 1 kHz, no load to full load) output power)
Direct Output < 0.5 dB 1407A (1/3 rd Max. 130 watts/3301BTU/hr
output power)
Transformer Output < 1.0 dB .
Signal-to-Noise Ratio > 100 dB Operating IC 0
(A-weighted, MASTER Temperature Range Up to 60 (140 F)
at full clockwise position, input shorted, pad Dimensions 5'/a" (13.3 cm) H x 14" (48.2
and high pass filter switched out) cm) W x 121/z" (31.7 cm) D

Connectors Weight
Input 1 - XLR fernale (Net)
1 - 5-lug screw terminal 1415A 30.8 Ibs (14 kg)
1- Phono 1407A 24.2 lbs (11 kg)

Output 1 - XLR male Color Black 2 - phono
1- 7-terminal barrier Included Accessories 1 - Operating/Service
strip Instructions
AC 1- Aux AC grounding outlet 1 - Shorting bar (Direct out to
(500 watts max) OT IN, installed)
4 - Rubber feet (installed)
Controls and indicators 1 - 220/240 voltage sticker
Front Panel 1 - Power on-off switch (for Int'l use)
1 - Power indicator LED 1 - Fuse sticker (for Int'l use)
1 - CLIP indicator LED 1- Fuse (for Int'I use)
1 - PROTECT indicator LED 1 - Rack mount hardware kit

Rear Panel 1- MASTER output level ALTEC LANSING continually strives to improve product control and performance. Therefore specifications are
1- 15 dB PAD switch subject to change without notice.

 

 


 

CLICK ON ANY IMAGE TO VIEW THAT EQUIPMENT SECTION

aLTEC aMPLIFIER aCCESSORIES SECTION Altec Microphone section Altec Mixer Section  
Altec Powered Mixers and Misc
Altec Signal Processing sections
 
Specifications Catalog Table of Contents

 

 

 

CLICK ON ANY IMAGE TO VIEW THAT EQUIPMENT SECTION